Technical Details

Native Custom Stone CustomFit® Details

Installation Details over Wood Studs

Over Open Stud Framing

Over Wood Studs w/ Batt Insulation

Over Wood Studs w/ Rigid Insulation

Over Wood Studs @ Grade

Installation Details over Wood Studs

Over Open steel Studs

Over Steel Studs w/ Batt Insulation

Over Steel Studs w/ Rigid Insulation

Installation Details on Masonry/Concrete

On CMU Wall

Native Custom Stone Cross Section Details

Adjacent Wood Trim

Below Wood Trim

Inside Corner – Cement or Plaster

Window Sill

Window Jamb

Window Header

Roof Eave

Chimney Cricket

Flashing at Tile Roof

Chimney Chase Cap Wood Trim

Roof Detail

Water Table | Wainscot

Outside Corner

Inside Corner

Wall & Cap

Wall Section TYP

Wood Frame/Concrete Wall

Wood Frame/Concrete Foundation

Flashing and Detail Notes

Native Custom Stone Superior Guard Installation

Installation Details over Wood Studs

Installation Details over Metal Studs

Superior Guard Residential Installation

Superior Guard Commercial Installation

Superior Guard Flashing and Detail Notes

Native Custom Stone Installation Instructions

Stone Installation Details

Stone Installation Diagrams

Disclaimer: These construction details are provided to assist in the installation of Native Custom Stone product(s). These construction details will not necessarily apply to every design circumstance that you encounter. These construction details may, and most likely will, require modifications to meet your particular design requirements. Manufacturer accepts no responsibility or liability for the use of these or other construction details. Our products are not intended to be exposed to direct flames, damages as a result of this will not be warranted by the manufacturer.

Native Custom Stone CustomFit® Details

Installation Details over Wood Studs

Over Open Wood Studs

Over Wood Studs w/ Batt Insulation

Over Wood Studs w/ Rigid Insulation

Installation Details over Metal Studs

Over Open Steel Studs

Over Steel Studs w/ Batt Insulation

Over Steel Studs w/ Rigid Insulation

Installation Details on Masonry/Concrete

On CMU Wall

Native Custom Stone CustomFit® Installation

Installation Details over Wood Studs

Panel Installation Instructions

Panel Assembly Elevation

Disclaimer: These construction details are provided to assist in the installation of Native Custom Stone product(s). These construction details will not necessarily apply to every design circumstance that you encounter. These construction details may, and most likely will, require modifications to meet your particular design requirements. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

Spec Data

Safety Data

IAPMO Report

ICC-ES Report

ICC-ES Report

ASTM Fire Rating – Go-Stone

ASTM Fire Rating

3-Part Spec

Safety Data

We want to make sure that you keep your custom stone looking great for years. Part of this is making sure that it’s well maintained and clean. As you know, manufactured stone veneer is different than a natural stone, and needs to be cared for differently. A good cleaning every two-three months should keep your manufactured stone looking new.

Keep in mind when installing your stone not to leave mortar on any surface. Mortar should be brushed away as the stone or brick is installed. If the surface is properly protected during the application, cleanup will be much easier. After the mortar sets for 24 hours, wash the job with a water hose to eliminate excess dust. Once the Stone or brick veneer has dried, apply a sealer for maximum protection.

5 Steps to Properly Cleaning Manufactured Stone Veneer:

  1. Thoroughly mix approximately one cup of Laundry detergent into 3 gallons of hot water.  Never use detergents with bleach, any type of acid, or a pressure washer.
  2. Rinse the stone/brick with water to remove loose debris.
  3. Using a circular motion scrub the dirtiest areas first using a medium bristle brush.
  4. Rinse the cleaned area thoroughly, removing all detergent and suds.
  5. Let dry, if you still see dirt and debris, repeat the cleaning process. Once completely dry and clean, seal.

Remember you don’t need to clean your manufactured stone often, if there is a little mud or muck just rinse with a hose or water. Or, if you have accent stone veneer inside your home, just wipe it down with a damp cloth.

They do make special detergents for manufactured stone if you wanted to keep it on the safe side, but a mild dish detergent or even laundry detergent will do. If you don’t have manufactured stone in your home yet, but have been thinking about it, Native Custom Stone has a wonderful selection of manufactured stone veneers to choose from. They also have distributors all over Georgia, and you can buy online from Build Direct or Home Depot!

Visit the Showroom

Visits to the Native Custom Stone Showroom are by appointment only. 
Call (888) 823-0745 today to schedule!

Find a Vendor

Close
Get Directions
'; ';
Options hide options
Print Reset
Fetching directions...

Contact Us

Fill out the form below, and our team will respond as soon as possible.

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
First Name*
Last Name*